Remote control introduction

by leealex

Key Description

1. Standby Key

Press this button to enter standby mode. Press it again to enter normal mode.
Note: Power consumption in standby mode is approximately half of the normal mode

2. Number Key

To set preset or call preset.

3. *Key

Used with other buttons.

4. Preset Key

Set preset: Store a preset position.

[SET PRESET] + Numeric button (0-9): Setting a corresponding numeric key preset position.

5. HOME Key

Confirm menu, enter the submenu or the PTZ will back to the middle position after pressed it

6. Return Key

Return back the last level menu

7. Zoom Key

Slow Zoom: Zoom In [+] or Zoom Out [-] slowly

Fast Zoom: Zoom In [+] or Zoom Out [-] fast

8. Left/Right Setting Key

Press with 1 buttons and 2 buttons setting the direction of the Pan-Tilt.

l  Simultaneously press L/R Set + 1 [STD]: set the Pan-Tilt turn the same direction as the L/R Set.

l  Simultaneously press L/R Set + 2 [REV]: set the Pan-Tilt turn the opposite direction as the L/R Set.

9. Focus Key

Used for focus adjustment.

Press [AUTO] adjust the focuses on the center of the object automatically.

Press [MANUAL] adjust the focus on the center of the object manual.

MANUAL button, and adjust it with [Far] (Focus on far object) and [NEAR] (Focus on near object).

10. Selection Key

Press the button corresponding to the camera you want to operate with the remote controller.

11. #Key

Used with other buttons.

12. IR Remote Control Key

[*]+[＃]+[F1]: Address 1

[*]+[＃]+[F2]: Address 2

[*]+[＃]+[F3]: Address 3

[*]+[＃]+[F4]: Address 4

13. Reset Key

Clear preset: Erase a preset position.

[CLEAR PRESET] + Numeric button (0-9)

Or: [*]+[#]+[CLEAR PRESET]: Erase all the preset individually.

14. PTZ Control Key

Press arrow buttons to perform panning and tilting. Press [HOME] button to face the camera back to front.

15. Menu Key

MENU: enter or exit OSD MENU.

16. Backlight Key

BLC ON/OFF: Press this button to enable the backlight compensation. Press it again to disable the backlight compensation.

NOTE:

l  Effective only in auto exposure mode.

l  If a light behind the subject, the subject will become dark. In this case, press the backlight ON/OFF button. To cancel this function, press backlight ON/OFF button.

17. PTZ Reset Key

Preset Pan/Tilt self-test.

18. Image Freezing Function

Manually freeze: Open the freezing function after press the remote control [F4], display “Freeze” on the left upper corner character, after five seconds display disappear automatically. If you want to cancel the freeze, press [F4] key and then can return to normal, display “Unfreeze” on the left upper corner, after five seconds display will disappear automatically.

Recalling the Preset image Freeze: By the OSD Menu “Image Freeze” to set recalling the preset image freeze function. After the function is opened, the screen will stay in before Recalling the Preset when Recalling the Preset, the screen can be switched to the preset position screen until the camera points to the preset position.

19. Shortcut Set

[*]+[＃]+[1]: OSD menu default English

[*]+[＃]+[3]: OSD menu default Chinese

[*]+[＃]+[4]: Display current IP address

[*]+[＃]+[6]: Quickly recover the default

[*]+[＃]+[8]: Look the camera version

[*]+[＃]+[9]: Quickly set up inversion

[*]+[＃]+[MANUAL]: Restore default IP
address

 

NOTE: If Remote control can not control

  • Check and replace the new battery for the remote controller.
  • Check whether the camera working mode is correct.
  • Check whether the address of remote control can match the camera

4 comments

  • Não consigo fazer nada com o controle. Tento resetar pelo comando mas não resolve… O que pode ser?
    [*]["]6: Recuperar rapidamente o padrão

    Hadson Lima

  • Button #10 allows you to select which camera you would like to control. I have two cameras and they both are defaulted to camera 1. How do I reassign one of them to camera 2 on the remote?

    Jan

  • My remote looks somewhat like this one and yet it is different. The manual that I received with the two cameras that I purchased leave much to the imagination. I am trying to figure out how to control the White Balance to cut down on the glare that I get off of objects in the field of view. The instructions say it is possible to change and not how to do it. Any assistance will be most helpful.

    Don Roden

  • I can’t set one of my two cameras to respond to the remote control.
    I point the remote at the camera, press * then #, then F1. No response to remote control.
    The second camera works fine.
    Please advise.

    Doug Hindman

Leave a comment

Back to How to use the camera